TRAINING PRACTICAL INTERNAL CORROSION CONTROL AND MONITORING IN OIL & GAS OPERATIONS

TRAINING PRACTICAL INTERNAL CORROSION CONTROL AND MONITORING IN OIL & GAS OPERATIONS

Training Praktis Pengendalian Korosi Internasional Dan Pemantauan Dalam Operasi Minyak & Gas

Training Catastrophic Effects Of Corrosive Agents And Microorganism In The Gas

training praktis pengendalian korosi internasional dan pemantauan dalam operasi minyak & gas murah

Internal Corrosion Problems in Gas, Oil and Produced Water Pipeline and Equipment
* Piping and Pipeline Leakage due to Pitting Corrosion and Microbiological Induced Corrosion
* Severe Pipe Wall Thickness Reduction and Short Remaining Service Life caused by Sour Corrosion
* Pipe Wall, Rotating Parts and Equipment Cracking due to Chloride and Sulfide in the Fluids
* Internal Corrosion of Pipeline and Equipment due to Water in Oil and Oil in Water Emulsions
* Internal Corrosion due to Multi Phase Flow in the Pipeline
* Severe Corrosion Rate caused by CO2 and Hydrate in the Gas Lines, CO2/H2S Removal Unit and Glycol Dehydration Unit
* Internal Corrosion in the Water Lines due to Dissolved Oxygen, Mud and Sludge
* Malfunction of Pump, Compressor, Valves and Equipment due to Under-Deposit Corrosion, Under-Film Corrosion and Fouling

The Nature, Mechanism and Characteristics of Internal Corrosion and the Control Methods
* Anodic-Cathodic Reactions, Electrical Properties and Characteristics of Corrosion Cells
* Physical & Metallurgical Conditions of Metals and Chemical Composition that Promote Corrosion
* Destructive and Catastrophic Effects of Corrosive Agents and Microorganism in the Gas, Oil and Produced Water Fluids
* The Role and Mechanism of O2, CO2, H2S, Dissolved Salts and Microorganism in Internal Corrosion
* The Role of Oilfield Bacteria and the Mechanism of MIC
* Characteristics and Detection of Internal Corrosion in the Pipeline and Surface Equipment
* Removal of Dissolved Corrosive Agents and Non-Hydrocarbon Gases in the Gas, Oil and Produced Water Fluids
* Internal Corrosion Control with On-line Chemical Inhibitors Injection, Surface Barriers and Scavengers

Internal Corrosion Detection and Monitoring  Techniques, Devices and Analysis
* Visual Inspection and Early Detection Techniques & Devices for Monitoring Fluid Corrosiveness and Tests for Identifying Corrosion products
* The Important of Internal Corrosion Rate Monitoring Before and After Chemical Injection and Treatment
* NACE Standard Method for Preparation, Installation, Laboratory Analysis and Interpretation of Results of Internal Corrosion Monitoring
* Access Fittings, Retrievers, Corrosion Coupons, Scale Coupons, Corrosion Probes,  Holders, Injection & Sampling Devices and Instrument for On-line Internal Corrosion Monitoring
* The Use of Nipple or Spool, Hydrogen Probe and Galvanic Probe
* NACE Standard Method for Testing and Analysis of Bacterial Activity and Microbiological Induced Corrosion
* Iron Content Analysis of Produced Water and the COPRA Correlation
* Down-hole Tubing or Casing Calipers, Ultrasonic Wall Thickness Testers and Radiography

Internal Corrosion Control with Chemical Inhibitor Injection, Passive Film Formation and Biocides
* Nature & Classification of Inhibitors and Effect of Ionic Character on
* Inhibiting Ability
* Formulations of Oilfield Inhibitors and the use of Water Soluble Inhibitors, Volatile Inhibitors and Acid Inhibitors
* Typical Corrosion Inhibitors, Scavengers & Biocides for Oil & Gas Field
* Guidelines of Inhibitor and Biocide Applications and the Chemical Injection Equipment for Pipeline and Surface Facility
* Inhibitor and Biocide Batch Treatment Using Pigs, Chemical Dosage and the Pigging Operations
* Surfactant and Cleaners for Solving Fouling Problem in the Equipment and Systems
* Cationic & Mixed Charge Organic Inhibitors for Hydrocarbon and Oxygen Corrosion Inhibitors for Produced Water
* Testing and Evaluation of Inhibitor and Biocide Effectiveness
* Safety Precaution in Working with Inhibitors and Biocides

Internal Corrosion Control as a Key Factor to Pipeline Integrity Management
* Hazard Assessment and Risk Based Inspection for the Pipeline and Equipment Maintenance Program
* Pipeline Internal Damage Record and Wall Thickness Monitoring
* Pigging for Water and Deposit Removal from the Pipeline System
* Controlling of Flow Stability and Corrosion Rate to a Safe Level
* Estimating Present Pipeline Remaining Service Life
* Evaluation of Present Condition and Comparison with Initial Pipeline Design Baseline
* Evaluation and Controlling of Chemical Inhibitor and Biocide Injection by using Corrosion Rate Monitoring Data.
* Evaluation of Pipeline and Equipment Damage in accordance with Root Cause Failure Analysis
* Development of Specific Pipeline Integrity Management System by using Internal Corrosion Rate Monitoring Data

Course Leader: Hilman Ahmad

This specially designed course will be conducted by Hilman Ahmad & Associates, an Independent Consultant in industrial oil and gas, member of the Society of Indonesian Petroleum Engineers, who manage the Professional Industrial Oil & Gas Education Center, and has been practicing production operation & safety and corrosion control engineering in Indonesia for more than twenty-five years. He post-graduated from Tokyo Institute of Technology (sponsored by UNESCO) in 1977. He joined in-field-practice program at Nippon Kokan Steel Company & Research Center Kawasaki, Japan for production facility design & construction and corrosion prevention & control in 1983, and collaborated with Cormon Industrial Research Center Brighton UK for on-line corrosion monitoring development in 2000. He has been delivering training course in production operation, maintenance & safety and corrosion control for personnel from Oil & Gas Company and Petrochemical Industry since 1979.

Jadwal training practical internal corrosion control and monitoring in

Jadwal Portal Cari Training 2024

 

  • batch 1 : 23 – 24 Januari 2024
  • batch 2 : 7 – 8 Februari 2024
  • batch 3 : 6 – 7 Maret 2024
  • batch 4 : 23 – 24 April 2024
  • batch 5 : 7 – 8 Mei 2024 || 21 – 22 Mei 2024
  • batch 6 : 11 – 12 Juni 2024
  • batch 7 : 17 – 18 Juli 2024
  • batch 8 : 21 – 22 Agustus 2024
  • batch 9 : 18 – 19 September 2024
  • batch 10 : 8 – 9 Oktober 2024 || 22 – 23 Oktober 2024
  • batch 11 : 5 – 6 November 2024 || 19 – 20 November 2024
  • batch 12 : 10 – 11 Desember 2024

Investasi dan Lokaspelatihan:

  • Yogyakarta
  • Jakarta
  • Bandung
  • Bali
  • Surabaya
  • Lombok

Catatan : Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.

Fasilitas :

  • FREE Airport pickup service (Gratis Antar jemput Hotel/Bandara/Stasiun/Terminal)
  • Module / Handout
  • Flashdisk
  • Sertifikat
  • FREE Bag or bagpackers (Tas Training)
  • Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
  • 2xCoffe Break & 1 Lunch, Dinner
  • FREE Souvenir Exclusive
  • Training room full AC and Multimedia
Tanyakan pada kami ?

We are here to help you! Do not hesitate to ask us anything. Click below to start chat.

Marketing

Aini

Online

Marketing

Maulana

Online

Aini

Hai, ada yang dapat kami bantu ? 00.00

Maulana

Hai, tanyakan pada kami ? 00.00
мега даркнет