TRAINING ALIGNMENT PUMP AND MOTOR

TRAINING ALIGNMENT PUMP AND MOTOR

Training Fundamental Alignment

Training Measuring Misalignment

training fundamental alignment murah

Description
Motor-Pump alignment is the process of aligning shaft centerlines between a motor and a pump. The motor is the prime mover, transferring power to the pump by the use of a coupling. This is probably the most common configuration of coupled machines in industry.
In this type of alignment, the motor is almost always the moveable machine, and the pump is the stationary machine. In almost all cases, the pump is already piped up with suction and discharge flanges, which means it can move only slightly, if at all.
motor-pump-alignmentProper shaft alignment is achieved by moving the motor. The motor is shimmed vertically to achieve the proper elevation to align it to the pump, both parallel (offset) and angular. The motor is them moved horizontally to achieve proper horizontal placement for aligning the shaft centerlines, both parallel and angular. The motor is moved horizontally by the use of jacking bolts, or by the use of pry bars, hammers, or other tools.
Motors are normally easier to move, since the motor is not piped into a process system. A short run of flexible conduit is most often used to run the electrical wiring from a local disconnect, or a rigid conduit, to the motor termination box. This allows for ease of movement of the motor.

Materi
1. Fundamental Alignment
2. Diagnosing Misalignment
3. Measuring Misalignment
4. Preparing Task Alignment
5. Alignment Methods (praktis)
•Rough Methods
•Face and Rim
6. Alignment Tolerances
7. Complicating Factor Alignment.
8. Introduction to Laser Alignment
9. Minimizes the forces of misalignment acting upon the bearings and seals of both components.
10. Minimizes Wear of The Coupling.
11. Reduce Energy Costs.
12. Maximizes the life of the Machine Components by Minimizing Wear, ncreasing time between failures, and reducing vibration.

Method
•Presentation
•Discussion
•Simulation
•Case Study
•Evaluation

Who Should Attend
Instrument Engineer/Supervisor, Plant Maintenance/Operators/Supervisors

Instructor
Mokhamad Munir Fahmi, Ir, MT. And Tim

Jadwal Portal Cari Training 2024

 

  • batch 1 : 23 – 24 Januari 2024
  • batch 2 : 7 – 8 Februari 2024
  • batch 3 : 6 – 7 Maret 2024
  • batch 4 : 23 – 24 April 2024
  • batch 5 : 7 – 8 Mei 2024 || 21 – 22 Mei 2024
  • batch 6 : 11 – 12 Juni 2024
  • batch 7 : 17 – 18 Juli 2024
  • batch 8 : 21 – 22 Agustus 2024
  • batch 9 : 18 – 19 September 2024
  • batch 10 : 8 – 9 Oktober 2024 || 22 – 23 Oktober 2024
  • batch 11 : 5 – 6 November 2024 || 19 – 20 November 2024
  • batch 12 : 10 – 11 Desember 2024

Investasi dan Lokaspelatihan:

  • Yogyakarta
  • Jakarta
  • Bandung
  • Bali
  • Surabaya
  • Lombok

Catatan : Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.

Fasilitas :

  • FREE Airport pickup service (Gratis Antar jemput Hotel/Bandara/Stasiun/Terminal)
  • Module / Handout
  • Flashdisk
  • Sertifikat
  • FREE Bag or bagpackers (Tas Training)
  • Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
  • 2xCoffe Break & 1 Lunch, Dinner
  • FREE Souvenir Exclusive
  • Training room full AC and Multimedia
Tanyakan pada kami ?

We are here to help you! Do not hesitate to ask us anything. Click below to start chat.

Marketing

Maulana

Online

Maulana

Hai, tanyakan pada kami ? 00.00
мега даркнет