TRAINING PRESSURE VESSEL AND PIPING DESIGN

Training Pengenalan Pressure Vesel

Training Desain Perpipaan

DESCRIPTION

In order to address the safety concerns associated with pressurized equipment and piping, these are required to be designed, fabricated and operated according to specified codes and standards. The commonly accepted codes are the ASME Sec. VIII Div. 1 for design of pressure vessels and ANSI B31.1 for design of piping. It takes a new engineer considerable time to understand that there is much more to pressure vessel design than calculation of hoop stress. The present course is designed to bridge the gap between the theoretical aspects of pressure vessel design and its industrial application. The faculty of this course would share their considerable experience to address the practical issues associated with pressure vessel design.
WHO SHOULD ATTEND

The course is aimed at engineers from Engineering and Manufacturing organizations who are involved in design and fabrication of pressure vessel and piping. It is anticipated that participants hold an engineering degree or have been involved for a good number of years in the design of vessels and piping. This course will be particularly appropriate for new engineers needing initial familiarity with application of ASME Code to the design and construction of pressure vessel and piping. It is also useful for engineers who have some experience of pressure vessel equipment and who wish to broaden their understanding of the behaviour of pressurized equipment.

PRESSURE VESSEL & PIPING DESIGN SUMMARY OUTLINE

1. Introduction to Pressure Vessel Design Codes
2. Design Basis and Design Criteria
3. Design for Internal pressure
4. Design for External Pressure
5. Design of Nozzles
6. Flange design
7. Design of Vessel supports
8. Design of Tubesheets
9. Fabrication
10. Examination
11. Testing
12. Computer codes for pressure vessel design
13. Case studies on failure of pressure vessels
14. Materials of construction for pressure vessels
15. Design of piping as per ANSI B31.1
16. Pressure, thermal and dynamic loads
17. System layout
18. Pipe supports and restraints
19. Piping flexibility, Flexibility factor and stress intensification factor
20. Computer codes for Piping analysis

COURSE METHOD
* Presentation
* Discuss
* Case Study
* Evaluation
* Simulation

• batch 1 : 23 – 24 Januari 2024
• batch 2 : 7 – 8 Februari 2024
• batch 3 : 6 – 7 Maret 2024
• batch 4 : 23 – 24 April 2024
• batch 5 : 7 – 8 Mei 2024 || 21 – 22 Mei 2024
• batch 6 : 11 – 12 Juni 2024
• batch 7 : 17 – 18 Juli 2024
• batch 8 : 21 – 22 Agustus 2024
• batch 9 : 18 – 19 September 2024
• batch 10 : 8 – 9 Oktober 2024 || 22 – 23 Oktober 2024
• batch 11 : 5 – 6 November 2024 || 19 – 20 November 2024
• batch 12 : 10 – 11 Desember 2024

Investasi dan Lokasi pelatihan:

• Yogyakarta
• Jakarta
• Bandung
• Bali
• Surabaya
• Lombok

Catatan : Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.

Fasilitas :

• FREE Airport pickup service (Gratis Antar jemput Hotel/Bandara/Stasiun/Terminal)
• Module / Handout
• Flashdisk
• Sertifikat
• FREE Bag or bagpackers (Tas Training)
• Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
• 2xCoffe Break & 1 Lunch, Dinner
• FREE Souvenir Exclusive
• Training room full AC and Multimedia